NOW OPEN & CUTTING Other machines I like to ride & fix

TESLAJET 2010 Component turbine store

Accepting Paypal, outside USA & Canada email for shipping cost.

Youtube progress videos.


The purpose of this page is to sell parts but also to encourage
some to build what they can imagine or need.
Main body parts 6061 aluminum plate.
All orders shipped airmail allow 2 weeks for delivery and customs,
Paypal transfer takes 3-4 days to Canada.

Safety NOTE to everyone:
These are simple but no one under a smart 15-16 should operate without an adult present.
A contest may be launched for best design/application by 2011 with a $300. prize, after 10 kit sales.
This intro pricing may change with material cost globally.
The stator case wall is 19mm thick to add strength. Easy to clamp "feet".

Against all my machinist sense but for those without one:


To save bending and damaging shafts I suggest trying
industrial heat cured bond or even JB quick weld w/48hr cure.
Clamp disk stack/washers & neo-back endwashers listed below.
Cure shaft/disk assembly* with outer plates less gasket(s) for pressure on centre between bearings.
*Use metal washers if heat curing.
If you then do not like the configuration
or it breaks you can make a new one or try to drift the old shaft out.
My demo unit is marine 2 part heat bonded and has
yet too fail or show wear with load.

These motors shock even me for durability.
Easy to service & 1.8kgs or less assembled so good for hiking & remote locations.
Burt Munroe of NZ made a 1920 motorcycle into a record holder
until past the 1980's so it's how things work not look that really counts.


The shaft getting hit is only real risk to operation imo.
The disks are safer/cheaper slipping than stripping a shaft and disk.
The large washer and shaft knurling provide excellent surface bonding
Little to no vibration in motor to cause fatigue cracks. Remember these are to build upon not just put on the shelf.
If impact, heavy constant loads or shock to shaft is a concern locking collars and
or a keyway/pinned collars w/set screws should be fitted of course.
I have hardened shafts to fit bearings this week with a flat for set screw.


Email for academic kit info and bulk quantity.
I build things to last, no comprimise for profit.
Proudly designed & made in Canada & USA, all workers paid a fair living wage.

A very detailed history with a lot of mystery.
Back to the vintage British bike store.

Quality CNC waterjet cut Component parts & 2.01 turbine accessories.Description vrs. 2.01 (25-120PSI)
Disk vrs. 2.28 228mm (9") Coming soon...
Price per unit
Complete 2.01 Ready to work TeslaJet turbine.
Great demo or attach 5/16" i.d. diameter pulley
will turn DC brushless motors for power. Inline fuse rec.
30psi - 120psi Rec-70-90psi AIR, STEAM, WATER & FLUIDS TO 100psi.
5.01 Brass SCD Nozzle installed to save presure. The valve shown for air only, steam use version comes with high pressure ball valve listed below. Display/Museum finish.
$585.00 Ready out of the box to your spec'd input.
Additional disks by quote. Small portable propane/fire boiler in design phase. Shaft machined flat matching disks for torque. DC or AC generators/dyno can be bolted to case. See latest video's generating DC current with easy mounting.UPDATE: Adding spin-up water drain at rear with lever valve. It will clear "wet steam" if built up avoiding the wait for turbine to expell it via vent.
+ S/H USD

PARTS BELOW TO BUILD THE ABOVE OR EVEN MORE POWERFUL
TURBINE GENERATOR.

Stator body: 1/2" wide, 97mm I.D., 137mm High, 185mm foot print width. (avrg. kerf deflection over .500" >1mm<) 6061 Aluminum .500" stator main body.
Stators can be stacked with gaskets & extended 5/16" dia shaft.
Polishing can be done but not done on demo.
$85.75 undrilled for input, design/machine your own nozzle input.
1/8"NPT input.
+ S/H USD
Stator body: 1/2" wide, 97mm I.D., 137mm High, 185mm foot print width. (avrg. kerf deflection over .500" >1mm<) Stainless steel 516.
Stators can be stacked with gaskets & extended 5/16" dia shaft.
Polishing can be done but not done on demo.
$175.50 undrilled for input, design/machine your own nozzle input.
1/8"NPT input.
+ S/H USD
97mm I.D., 137mm High, 185mm foot print width. (avrg. kerf deflection over .500" >1mm<)
(1) 5/16" hole, tapped to 1/8" NPT.(A metering valve will act as nozzle,
Pressfit inserts could be fabricated) 6061 Aluminum .500" stator main body.
Stators can be reversed w/2 holes, stacked with gaskets & extended 5/16" dia shaft.
Polishing can be done but not done on demo).
$102.75 drilled/tapped for input,
1/8"NPT input.
+ S/H USD
Stator body: 1/2" wide, 97mm I.D., 137mm High, 185mm foot print width. (avrg. kerf deflection over .500" >1mm<) Stainless steel 516.
Stators can be stacked with gaskets & extended 5/16" dia shaft.
Polishing can be done but not done on demo.
$199.50 .334" drilled for (1) input, design/machine your own nozzle input.
1/8"NPT input threading.
+ S/H USD
608z bearing plate w/bearing .250" 6061 Aluminum, 2 required.
The purpose in the design of this plate is for mounting small wound coils that can be charged by press-fit magnets in outer rotors face.
3- 1/16" flange gaskets required to gain clearance. See "Electrics" below.
$43.50
+ S/H USD
Outer vented cover .125" 6061 Aluminum. 2 required. $24.50
+ S/H USD
(1) Standard 6061 Aluminum TeslaJet style flat drive rotor disk.
Shown in assembled stator shell not incl. 95mm x 1.2mm x 5/16 I.D. shaft hole.
$9.50/e
+ S/H USD
(1) Stainless STEEL TeslaJet style flat drive rotor disk.
Shown in assembled stator shell not incl. 95mm x 1.2mm x 5/16 I.D. shaft hole.
$155.50/e
N.A. Postage incl.
Aluminum Pelton style flat cupped drive rotor (require shim washers, 3 fit.), 95mm x .125" x 5/16" I.D.. $15.50/e
N.A. Postage incl.
Aluminum "Nautilus" Pump and liquid drive rotor, vents well for steam.
2 shown stack mounted to 1/4" on 1.2mm flat Tesla disk at back.
(stack and bond, 3 fit.), 95mm x .125" x 5/16" I.D..
$27.50/e
+ S/H USD
Non-vented end flange, 6061 Aluminum 5/16" I.D. x 2-5/16" O.D. x .250" $13.50
+ S/H USD
Lexan end flange cover, 5/16" I.D. x 2-5/16" O.D. x 3/16" $10.50
(2) 608z semi-sealed bearings, 40 000+rpm. $5.75
N.A. Postage incl.
(1) 4" stainless steel (snug fit near Class 4-Zero allowance, knurling for 1/2" disk area.) bearing shaft for 608 bearings, 40 000rpm. slightly over 5/16"/8mm for metal to metal with hand assembly. $8.75
N.A. Postage incl.
(1) 6" Stainless steel (snug fit near Class 4-Zero allowance, knurling for 1/2" disk area.) bearing shaft for 608 bearings, 40 000rpm. slightly over 5/16"/8mm for metal to metal with hand assembly. No disk "flat". $13.75
N.A. Postage incl.
-------- Stainless steel screws, accessories, structural spacer CF/NBR gaskets. --------
1/64" Carbon Fiber NBR rubber binded large flange gasket. Good to 1000psi, steam liquid MilSpec. $3.75
N.A. Postage incl.
1/32" Carbon Fiber NBR rubber binded large flange gasket. Good to 1000psi, steam liquid MilSpec. $5.75
N.A. Postage incl.
1/16" Carbon Fiber NBR rubber binded large flange gasket. Good to 1000psi, steam liquid MilSpec. For stacking to make pancake coil for DC generation. $8.75
N.A. Postage incl.
3/16" x 5/8"L Stainless cap screws for Lexan and outer flange (3). $5.50
N.A. Postage incl.
Main stator flange HG allen cap stainless screws 3/16"F x 1.75", (8) w/8 nylock nuts. $14.50
NA. Postage incl.
Main stator flange HG allen cap stainless screws 3/16"F x2.5", (8) w/8 nylock nuts. $18.50
(8) Main stator flange brass washers 3/16"i.d. x3/8" o.d.". $2.50
(4) 5/16" Neoprene backed threadseal stainless washers, slight cone excellent for bonding to shaft/plates. With gaskets shimming is a matter of minutes so fitting can be less than exact and still function well. $5.50
(10 Pair) 5/16" Thin steel washers >1mm<, med 5/8" o.d. & large fit 5/8" + .5mm i.d., 1"/25mm o.d." for spacing or bonding to shaft/plates. These combined can adapt 3.5" 95mm HDD disks with kevlar fibers or bonding spacer gaskets in 2 part industrial epoxy. $10.50
15 Feet Kevlar thread for composite bonding repair,fabrication or fixing. $4.50
10 Feet pure copper tape for loose thread repair/sealing,fabrication or electrics. $2.50
Coil diameter x Pi 3.14159 (the irrational number)
x
# windings
= Length/coil (add leads).
High quality high heat insulated magnet coil wire, new.
Solders well, 3 colours available for 3 phase wiring when permenant magnets are mounted/bonded to outer disk faces. Internal DC/AC power output when encapsulated with epoxy joining outer and bearing case.
Price per 10' foot length.
Limited supply for prototyping.
(10ft) AWG 23 Red High heat insulated mag wire for coils. $2.50 /10'
(10ft) AWG 23 Gold colour High heat insulated mag wire for coils. $2.50 /10'
(10ft) AWG 23 Green High heat insulated mag wire for coils. $2.50 /10'
-------- Live steam/Air/Fluid Brass & steel NPT fittings. m-male f-female threads.
All helpful and N.A. made.
--------
(1) Roll teflon sealing tape for threads. $2.35
(1) Brass CDN made 1/8"m to 1/4"f NPT fitting. $4.50
(1) Brass CDN made pneumatic tire valve - 1/4"m NPT fitting. $8.50
(1) Steel CDN made pneumatic shrt end (1/4" home compressor) quick connect - 1/4"m NPT fitting. $7.50
(1) Steel CDN made pneumatic long end quick connect - 1/4"m NPT fitting. $7.50
(1) Brass High pressure steam CDN made female to female - 1/8"m NPT valve. $8.50
(1) Brass CDN made Garden hose f - 1/4"m NPT (3) fittings combined. $12.50
(1) Brass CDN made 1/8"m - 1/4"m NPT fitting. $4.50
(1) Brass CDN made 1/4"m - 1/4"m union NPT fitting. $3.50 + S/H USD
With the parts above (multiple disks) a motor capable of several amps should be possible. Longer output shafts require more bearings etc.
SUPPORT SMALL MANUFACTURERS.
PEOPLE & TOOLS ARE WHAT MAKE THE WORLD A GREAT PLACE. Copyright Jan 13th 2010
Canadian Made.
This is (4) 2.01 alloy standard 95mm Tesla disks at 100psi...
imagine 48 disks!